Bill,
Feel free to be the guinea pig and bounce some models off the pool noodle
to see how well they work :)
Jake
On Fri, Jun 2, 2017 at 12:01 PM, William Gowen wdgowen_at_gmail.com
[Indoor_Construction] <Indoor_Construction_at_yahoogroups.com> wrote:
>
>
> Excellent!
>
> On Jun 2, 2017 2:07 PM, "Jake Palmer 82.jake_at_gmail.com
> [Indoor_Construction]" <Indoor_Construction_at_yahoogroups.com> wrote:
>
>>
>>
>> As a consolation, we are going to try Leo's pool noodle idea. Dollar
>> Tree sells 4 foot long noodles for a buck each, so the cost is very
>> minimal. They can be installed and removed without a lift rental, so
>> they're well within budget.
>>
>> On Fri, Jun 2, 2017 at 10:55 AM, William Gowen wdgowen_at_gmail.com
>> [Indoor_Construction] <Indoor_Construction_at_yahoogroups.com> wrote:
>>
>>>
>>>
>>> Thanks for trying!
>>>
>>> On Jun 2, 2017 1:04 PM, "Jake Palmer 82.jake_at_gmail.com
>>> [Indoor_Construction]" <Indoor_Construction_at_yahoogroups.com> wrote:
>>>
>>>>
>>>>
>>>> I just heard back from my contacts at Kibbie, and while they can hang
>>>> this plastic, it's simply too expensive. The donation from SAM 8 would
>>>> cover most of the cost to rent a lift, but the material and labor costs
>>>> push it well over the top. Perhaps next year I can line up enough funding
>>>> to make it happen.
>>>>
>>>> Jake
>>>>
>>>> On Thu, Jun 1, 2017 at 5:58 PM, <82.jake_at_gmail.com> wrote:
>>>>
>>>>> It sounds like they will need to rent a lift to get this done, but it
>>>>> might still happen. SAM 8 made a generous donation again this year, and
>>>>> that may be enough to cover the extra cost. I should have a better answer
>>>>> by next week.
>>>>>
>>>>>
>>>>>
>>>>> Sent from Mail <https://go.microsoft.com/fwlink/?LinkId=550986> for
>>>>> Windows 10
>>>>>
>>>>>
>>>>>
>>>>> *From: *William Gowen wdgowen_at_gmail.com [Indoor_Construction]
>>>>> <Indoor_Construction_at_yahoogroups.com>
>>>>> *Sent: *Thursday, June 1, 2017 4:00 PM
>>>>> *To: *Indoor_Construction_at_yahoogroups.com
>>>>> *Subject: *Re: [Indoor_Construction] Re: Question for Kibbie Dome
>>>>> attendees
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> I'm dreaming of bouncing my LPP off the plastic after a full torque
>>>>> launch.
>>>>>
>>>>>
>>>>>
>>>>> On Thu, Jun 1, 2017 at 5:59 PM, Jake Palmer 82.jake_at_gmail.com
>>>>> [Indoor_Construction] <Indoor_Construction_at_yahoogroups.com> wrote:
>>>>>
>>>>>
>>>>>
>>>>> I've made the request to have this plastic sheeting installed on each
>>>>> side of the curtain rods. I'll send out a notification once I have a
>>>>> definitive answer about whether it will happen.
>>>>>
>>>>>
>>>>>
>>>>> Jake
>>>>>
>>>>>
>>>>>
>>>>> On Wed, May 31, 2017 at 4:38 PM, guyettevan_at_yahoo.com
>>>>> [Indoor_Construction] <Indoor_Construction_at_yahoogroups.com> wrote:
>>>>>
>>>>>
>>>>>
>>>>> I think this is a great idea. I'd rather my model drop to 120ft than
>>>>> head for the wire forest in the center. Thank you Jake for looking into
>>>>> this!
>>>>>
>>>>>
>>>>>
>>>>> Evan
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>
>>>>
>>
>
Received on Fri Jun 02 2017 - 19:03:58 CEST