Re: Re: Question for Kibbie Dome attendees

From: William Gowen <wdgowen_at_gmail.com>
Date: Fri, 2 Jun 2017 15:01:51 -0400

Excellent!

On Jun 2, 2017 2:07 PM, "Jake Palmer 82.jake_at_gmail.com
[Indoor_Construction]" <Indoor_Construction_at_yahoogroups.com> wrote:

>
>
> As a consolation, we are going to try Leo's pool noodle idea. Dollar Tree
> sells 4 foot long noodles for a buck each, so the cost is very minimal.
> They can be installed and removed without a lift rental, so they're well
> within budget.
>
> On Fri, Jun 2, 2017 at 10:55 AM, William Gowen wdgowen_at_gmail.com
> [Indoor_Construction] <Indoor_Construction_at_yahoogroups.com> wrote:
>
>>
>>
>> Thanks for trying!
>>
>> On Jun 2, 2017 1:04 PM, "Jake Palmer 82.jake_at_gmail.com
>> [Indoor_Construction]" <Indoor_Construction_at_yahoogroups.com> wrote:
>>
>>>
>>>
>>> I just heard back from my contacts at Kibbie, and while they can hang
>>> this plastic, it's simply too expensive. The donation from SAM 8 would
>>> cover most of the cost to rent a lift, but the material and labor costs
>>> push it well over the top. Perhaps next year I can line up enough funding
>>> to make it happen.
>>>
>>> Jake
>>>
>>> On Thu, Jun 1, 2017 at 5:58 PM, <82.jake_at_gmail.com> wrote:
>>>
>>>> It sounds like they will need to rent a lift to get this done, but it
>>>> might still happen. SAM 8 made a generous donation again this year, and
>>>> that may be enough to cover the extra cost. I should have a better answer
>>>> by next week.
>>>>
>>>>
>>>>
>>>> Sent from Mail <https://go.microsoft.com/fwlink/?LinkId=550986> for
>>>> Windows 10
>>>>
>>>>
>>>>
>>>> *From: *William Gowen wdgowen_at_gmail.com [Indoor_Construction]
>>>> <Indoor_Construction_at_yahoogroups.com>
>>>> *Sent: *Thursday, June 1, 2017 4:00 PM
>>>> *To: *Indoor_Construction_at_yahoogroups.com
>>>> *Subject: *Re: [Indoor_Construction] Re: Question for Kibbie Dome
>>>> attendees
>>>>
>>>>
>>>>
>>>>
>>>>
>>>> I'm dreaming of bouncing my LPP off the plastic after a full torque
>>>> launch.
>>>>
>>>>
>>>>
>>>> On Thu, Jun 1, 2017 at 5:59 PM, Jake Palmer 82.jake_at_gmail.com
>>>> [Indoor_Construction] <Indoor_Construction_at_yahoogroups.com> wrote:
>>>>
>>>>
>>>>
>>>> I've made the request to have this plastic sheeting installed on each
>>>> side of the curtain rods. I'll send out a notification once I have a
>>>> definitive answer about whether it will happen.
>>>>
>>>>
>>>>
>>>> Jake
>>>>
>>>>
>>>>
>>>> On Wed, May 31, 2017 at 4:38 PM, guyettevan_at_yahoo.com
>>>> [Indoor_Construction] <Indoor_Construction_at_yahoogroups.com> wrote:
>>>>
>>>>
>>>>
>>>> I think this is a great idea. I'd rather my model drop to 120ft than
>>>> head for the wire forest in the center. Thank you Jake for looking into
>>>> this!
>>>>
>>>>
>>>>
>>>> Evan
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>
>>>
>
>
Received on Fri Jun 02 2017 - 19:01:54 CEST

This archive was generated by Yannick on Sat Dec 14 2019 - 19:13:48 CET