Foam is being installed now. They also installed new protective covers
over the curtain rods that should hopefully be less "grabby" for models.
You can see the foam and the new cover in the attached photo.
On Mon, Jun 5, 2017 at 12:57 PM, Jake Palmer <82.jake_at_gmail.com> wrote:
> One final follow up to this post. We've settled on some pipe insulation
> that's about 2-3/8" OD. It will be installed on every cable (12 cables per
> rod) up to 24 feet above the rod or the ceiling, whichever comes first. If
> this works, we'll save the foam and reinstall it each year.
>
> On Sat, Jun 3, 2017 at 2:41 PM, Ron Patten ronald.patten_at_att.net
> [Indoor_Construction] <Indoor_Construction_at_yahoogroups.com> wrote:
>
>>
>>
>> thanks . . .
>>
>>
>> On Friday, June 2, 2017 10:13 PM, "Jake Palmer 82.jake_at_gmail.com
>> [Indoor_Construction]" <Indoor_Construction_at_yahoogroups.com> wrote:
>>
>>
>>
>> sam8.org
>>
>> On Jun 2, 2017 7:18 PM, "Ron Patten ronald.patten_at_att.net
>> [Indoor_Construction]" <Indoor_Construction_at_ yahoogroups.com
>> <Indoor_Construction_at_yahoogroups.com>> wrote:
>>
>>
>> Jake,
>>
>> Can I have SAM 8's website and contact info, I seem to have deleted it?
>>
>> Ron Patten
>>
>>
>> On Thursday, June 1, 2017 8:31 PM, "82.jake_at_gmail.com
>> [Indoor_Construction]" <Indoor_Construction_at_ yahoogroups.com
>> <Indoor_Construction_at_yahoogroups.com>> wrote:
>>
>>
>>
>> [Attachment(s)
>> <https://mg.mail.yahoo.com/neo/launch?.partner=sbc&.rand=dgvtpr0qpi8bg#TopText>
>> from 82.jake_at_gmail.com included below]
>> It sounds like they will need to rent a lift to get this done, but it
>> might still happen. SAM 8 made a generous donation again this year, and
>> that may be enough to cover the extra cost. I should have a better answer
>> by next week.
>>
>> Sent from Mail <https://go.microsoft.com/fwlink/?LinkId=550986> for
>> Windows 10
>>
>> *From: *William Gowen wdgowen_at_gmail.com [Indoor_Construction]
>> <Indoor_Construction_at_yahoogroups.com>
>> *Sent: *Thursday, June 1, 2017 4:00 PM
>> *To: *Indoor_Construction_at_ yahoogroups.com
>> <Indoor_Construction_at_yahoogroups.com>
>> *Subject: *Re: [Indoor_Construction] Re: Question for Kibbie Dome
>> attendees
>>
>>
>> I'm dreaming of bouncing my LPP off the plastic after a full torque
>> launch.
>>
>> On Thu, Jun 1, 2017 at 5:59 PM, Jake Palmer 82.jake_at_gmail.com
>> [Indoor_Construction] <Indoor_Construction_at_ yahoogroups.com
>> <Indoor_Construction_at_yahoogroups.com>> wrote:
>>
>>
>> I've made the request to have this plastic sheeting installed on each
>> side of the curtain rods. I'll send out a notification once I have a
>> definitive answer about whether it will happen.
>>
>> Jake
>>
>> On Wed, May 31, 2017 at 4:38 PM, guyettevan_at_yahoo.com
>> [Indoor_Construction] <Indoor_Construction_at_ yahoogroups.com
>> <Indoor_Construction_at_yahoogroups.com>> wrote:
>>
>>
>> I think this is a great idea. I'd rather my model drop to 120ft than head
>> for the wire forest in the center. Thank you Jake for looking into this!
>>
>> Evan
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>>
>
>
- application/x-ygp-stripped attachment: stored
Received on Thu Jun 15 2017 - 19:49:59 CEST